New Bags
Brownstone_Image
Graystone_Image
Sandstone_Image
Brownstone_ti
Graystone_ti
Sandstone_ti

NOW AVAILABLE - JOINT-LOCK™ HP STONE (High Performance) - (Click Here for Spec Sheet.
Use for wide joints 1/2" to 3" - Perfect for Flagstone and Belgium Block Installation.

jl_hp_stone

Product Description:

JOINT-LOCK™ SAND is a polymer modified paver-finishing sand that is specifically designed to complement and enhance any paver installation. It is available in three colors Gray (Graystone), Tan (Sandstone), or Red/Brown (Brownstone). JOINT-LOCK™ Sand sets hard to resist weed growth, insect mining and erosion. It will resist scouring caused by sweeping, water rinsing and traffic.
(Product Spec Sheet - Instructions) and (Product Brochure)

Composition & Materials:

JOINT-LOCK™ SAND is a uniformly blended mixture of top quality mason sand with a polymeric additive. When activated (by water), JOINT-LOCK™ forms a firm barrier -- Like a one piece flexible joint. JOINT-LOCK™ will become pliable when it is subject to moisture such as rain or when rinsing with a hose, and will re-harden as it dries, forming a strong yet pliable joint.

JOINT-LOCK™ SAND, while easy to use, requires a few basic steps to prevent unnecessary clean up or extra work. To create a long lasting paving stone terrace, patio, or driveway, use JOINT-LOCK™ between the paving stone joints for maintenance free enjoyment for years to come. Our fine blend of quality mason sands and organic polymers provide a long lasting environmentally friendly solution to your next paving stone project.


    Make sure that the surface of the pavers and the paver joints are free of debris and completely dry before applying JOINT-LOCK™ SAND. The weather forecast should be rain free for 12 hours after application to ensure optimum bonding and product performance.
    Pour JOINT-LOCK™ SAND evenly over the entire area to be finished. Sweep JOINT-LOCK™ repeatedly over the joints until they are completely and uniformly filled. For best results fill the joints to 1/8" below the top surface of the pavers. DO NOT USE A FILLER SAND AS IT WILL COMPROMISE THE STRENGTH OF THIS PRODUCT.
    Use a gas powered plate compactor to compact the sand between the joint of the pavers. this will ensure all voids are filled, repeat steps 2 & 3 as necessary. After compaction sweep off all extra sand. If pavers are coarse use a leaf blower on lowest setting to clear off the paver surface.

    After you have ensured that the paver surface is completely free of sand, lightly but thouroughly saturate the area. (For best results do the saturation in 50-100 sq ft stages). The objective is to soak the area as deeply as possible in a controlled manner. Using too much water will float the polymer sand out of the joints resulting in deposits on the paver surface. Repeat this step 3 times allowing 10 minutes intervals between soakings. Make sure the paving stones are free of car and foot traffic for 18-24 hours following application of JOINT-LOCK™ SAND.

      (Printable Instructions)
      3 STEPS TO INSTALL PAVING STONES

Make sure to clear all weeds and debris between the pavers so JOINT-LOCK™ SAND will be able to bond to the paver joints.

Using a gas powered pressure washer clean the paver joints of the existing sand to the full depth of the paver. Let the area dry completely and then follow steps 1-4 (New Installation) above.

Joint Lock Demo

(See Product Demo)

line

The area should remain traffic free for 24 hours following the application of JOINT-LOCK™ SAND. JOINT-LOCK™ requires very little maintenance after the initial installation. Avoid using JOINT-LOCK™ in areas of persistent dampness (pools) or on sloping grades greater than 5 degrees. If an area needs sand replenishment simply follow the steps above.

 

safety and handling

Wear a dust mask, goggles and gloves while using this product. Handle and store in a manner to avoid dusty conditions. If the product comes in contact with your eyes, flush thoroughly and repeatedly with water. DO NOT RUB EYES. Wash hands after use. Do not take internally.

This product may contain silica. Prolonged inhalation may cause lung damage.

KEEP OUT OF REACH OF CHILDREN

 

Interested in becoming a Distributor ?

If your business is located in the Northeast (NY, NJ, CT, MA, VT, PA, DE, MD, VA) and you are interested in learning more about distributing Joint Lock Sand contact us for more info.

sales@packagepavement.com

(Product Brochure - New) - (Click Here)

Spec Sheet - Product Information (Click Here)

MSDS Information (Click Here)

New Product & Samples ... JOINT-LOCK™ product samples are available for shipment. Click here, please include your address and contact information.

NEW COLOR.... Now Available JOINT-LOCK™ SAND BROWNSTONE. A red colored sand for enhancing any paving stone application is now available for pickup or delivery. Call us today for a product sample and more information.

JOINT-LOCK™ Stone Dust is now available. Packaged in 70# Bags, (40% more material than other brands), JOINT-LOCK™ Stone is available in pallet quantities for delivery. Check back soon for Spec Sheets and MSDS for this product. Call for more info. (800) 724-8193.

 

To be added to any future mailing or to request more information contact us at sales@packagepavement.com


As licensed QUIKRETE® and SPEC MIX® manufacturers, PACKAGE PAVEMENT™, offers customers in the Tri-State area including Metro New York, Central New York, Western Connecticut, Berkshire County in Massachusetts and Western Vermont, the opportunity to receive premium quality products for pickup, or, with delivery options among the most timely and professional in the industry.
WEBSITE DISCLAIMER INFO.

  © 2008 Package Pavement Co. Inc.

 
www.quikrete.com
www.specmix.com
www.paypal.com